Puncte De Interes Romania - PDI / POI / GPS Romania

[VanCroft]

Buna. Problema ar fi asa: i-am pus pe card iGO8 si a mers bine dupa care l-am dat jos si am pus la loc softul original Mireo Black edition 3.0.Nu am umblat la memoria aparatului numai la card.A mers o juma de zi dupa care s-a blocat pe harta.Butonul de on/off nu mai functiona asa ca i-am dat un reset, dupa care s-a aprins dar ramane blocat pe imaginea din start cu Nort Cross si nici la calculator nu se mai conecteaza. Nu stiu ce sa-i mai fac.Am citit aici pe forum ca trebuie sa-l conectez la calc. cu AtlasMgr 5.8.7 si sa-l resoftez dar nu-l vede nici Atlasul. Va rog ajutati-ma.

[ablbd]

1 Scoate cardul, conecteaza cu pc si da-i un reset; daca cere drivere, le selectezi pe cele de la atlasmgr.
2. Daca nu vrea atunci tine apasat si mentine on-off inca 5-10 sec dupa reset.

In ultima instanta scoate bateria si repeta 2

[VanCroft]

Multumesc pentru raspuns . Am facut ce mi-ai scris la punctul 1 si i-am dat sa-si ia driverul de la Atlas Mgr 5.8.7 ; si-a copiat fisierele si mi-a scris ca s-a efectuat cu succes dar tot nu-l vede calculatorul; la puntul 2 la fel am facut ce ai scris dat imi zice tot USB Device Not Recognized, iar la chetia cu bateria , am desfacut aparatul dar firele de la baterie sunt lipite de cablaj.E vreo metoda mai usoara de a o scoate ?

[ablbd]

Pai dupa instalarea driverelor porneste atlasmgr, reset si cind se aude ton de usb, "open"

[VanCroft]

Tot nu vrea sa-l vada Atlasmgr. Cred totusi ca nu s-au instalat driverele bine pentru ca i-am dat inca o data sa le instaleze si zicea ceva ca nu e in regula.Tonul de usb se aude.Oare ce sa-i mai fac? Si pe calculatorul de la servici aceeasi treaba chiar daca acolo zice ca s-au instalat driverele corect.

[VanCroft]

Nu ma poate ajuta nimeni?

[chacka]

Dupa tonul USB ai max. 1 sec. sa apesi butonul OPEN din AtlasMgr

[VanCroft]

Aha o sa incerc. Iti multumesc mult.O sa scriu daca am reusit. Trebuie sa fac ceva setari sau sa bifez ceva la AtlasMgr inainte sa ma apuc de treaba? E bifat la transport USB , apoi COM1 , 38400 bps si chipul Atlas , Are acolo la flash type: SLC Nandf si MLC Norf - e bifat MLC Norf iar dedesubt la Norflash Type e pus SPANSION.....BOTTOMBOOT. Ebine nu ?

In sfarsit s-a cuplat la AtlasMgr. Problema acum e ca nu apar optiunile X 9 si U de care zicea domnul ablbd intr-o alta postare. Acolo la USB terminal sunt asa: 1):EB2 2):NK 3):DM 4):TOC 5):Mu 6):Clk iar active sunt butoanele Update NBOOTsi Update EBoot Ce trebuie sa fac acum ?

[ablbd]

Acesta este meniul scurt nboot. Alege 1 si enter.

[VanCroft]

Trebuie sa am cardul cu firmware in aparat ? Am dat 1 cu un card in aparat si mi-a scris asa 1):EB2
2):NK
3):DM
4):TOC
5):Mu
6):Clk
Microsoft Windows CE Ethernet Bootloader Common Library Version 1.1 Built Feb 17 2009 10:22:44
Centrality Windows CE Atlas Bootloader Version 3.2 Built Feb 17 2009 10:22:17
dwCacheInfo = 0x1D152152
EBOOT Version = 0x300B
TOC {
dwSignature: 0x434F544E
BootCfg {
ConfigFlags: 0x3860
BootDelay: 0xF
ImageIndex: 1
IP: 0.0.0.0
MAC Address: 00:00:00:00:00:00
Port: 0.0.0.0
SubnetMask: 0.0.0.0
}
ID[0] {
dwVersion: 0x300B
dwSignature: 0x45424F54
String: 'eboot.nb0'
dwImageType: 0x2
dwTtlSectors: 0x280
dwLoadAddress: 0x8C04C000
dwJumpAddress: 0x8C04C000
dwStartBlock: 0x2
dwStoreOffset: 0x0
sgList[0].dwSector: 0x80
sgList[0].dwLength: 0x280
}
ID[1] {
dwVersion: 0x1
dwSignature: 0x43465348
String: 'PPC2K3.NB0'
dwImageType: 0xE
dwTtlSectors: 0x523
dwLoadAddress: 0x8C750000
dwJumpAddress: 0x8C751000
dwStartBlock: 0x33
dwStoreOffset: 0x0
sgList[0].dwSector: 0xCC1
sgList[0].dwLength: 0x523
}
chainInfo.dwLoadAddress: 0x8C44C000
chainInfo.dwFlashAddress: 0x000054A1
chainInfo.dwLength: 0x00000008
nandxipInfo.dwCodePages: 0
nandxipInfo.dwCopies: 0
nandxipInfo.dwBlockNo: 0x00000000
nandxipInfo.dwCodePages: 0
nandxipInfo.dwCopies: 0
}
Image block starts at physical block 51 virtual block 51
WARNING: OEMPlatformInit failed to initialize Ethernet controller.
g_iDevStatus = D!

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
SDMMC card is detected!
Command or data time out!
SDMMC_Init successfully!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
! Now we try to update image from SD card. Please ensure
! your Monolithic or MultiXIP image in SD card root dire-
! ctory. Note here you must place only Monolithic or Mul-
! tiXIP image in SD card. If you select to doenload Mono-
! lithic image and put MultiXIP image in SD card, there
! will be errors! Vice versa. Here you have three choice:
! 1 ----- MultiXIP
! 2 ----- Monolithic
! 9 ----- Give up to download image
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Do what you want to download: input 1
Try to download MultiXIP image.
Can't open chain.lst file!
Download Monolithic image failed!
Press [ENTER] to download image now, or [SPACE] to enter boot monitor.

Initiating image download in 0 seconds.
OEMPlatformInit: IMAGE_TYPE_RAMIMAGE|IMAGE_TYPE_BINFS
INFO: Loading image from Boot Media to RAM (address=0x8C750000, sectors=0x523, launch address=0x8C751000)...
IsValidMBR: MBR sector = 0xCC0

OpenPartition: Partition Exists=0x1 for part 0x21.

BP_SetDataPointer at 0x0

ReadData: Start = 0x0, Length = 0x291800.

Log2Phys: Logical 0x1 -> Physical 0xCC1

Using device name: 'AT4X0HH_0'
-OEMPreDownload: BL_JUMP
::OEMLaunch, ImageStart:0x0, ImageLength:0x0, LaunchAddr:0x0
Eboot setup Kitl from media boot
INFO: using TOC[1] dwJumpAddress: 0x8C751000

Jumping to image at virtual address 0x8C751000h
+ToPhysicalAddr:0x8C751000
-ToPhysicalAddr:0xC0751000

::: Physical Launch Address: 0xC0751000h
Nu am dat 9 pentru ca aveam cardul cu Mireo in aparat. Am asteptat putin si s-a activat butonul close pe care am apasat si apoi am scos cardul.Dupa aceea m-am conectat iar la AtlasMgr fara card in aparat si mi-a aparut asa
1):EB2
2):NK
3):DM
4):TOC
5):Mu
6):Clk
Microsoft Windows CE Ethernet Bootloader Common Library Version 1.1 Built Feb 17 2009 10:22:44
Centrality Windows CE Atlas Bootloader Version 3.2 Built Feb 17 2009 10:22:17
dwCacheInfo = 0x1D152152
EBOOT Version = 0x300B
TOC {
dwSignature: 0x434F544E
BootCfg {
ConfigFlags: 0x3860
BootDelay: 0xF
ImageIndex: 1
IP: 0.0.0.0
MAC Address: 00:00:00:00:00:00
Port: 0.0.0.0
SubnetMask: 0.0.0.0
}
ID[0] {
dwVersion: 0x300B
dwSignature: 0x45424F54
String: 'eboot.nb0'
dwImageType: 0x2
dwTtlSectors: 0x280
dwLoadAddress: 0x8C04C000
dwJumpAddress: 0x8C04C000
dwStartBlock: 0x2
dwStoreOffset: 0x0
sgList[0].dwSector: 0x80
sgList[0].dwLength: 0x280
}
ID[1] {
dwVersion: 0x1
dwSignature: 0x43465348
String: 'PPC2K3.NB0'
dwImageType: 0xE
dwTtlSectors: 0x523
dwLoadAddress: 0x8C750000
dwJumpAddress: 0x8C751000
dwStartBlock: 0x33
dwStoreOffset: 0x0
sgList[0].dwSector: 0xCC1
sgList[0].dwLength: 0x523
}
chainInfo.dwLoadAddress: 0x8C44C000
chainInfo.dwFlashAddress: 0x000054A1
chainInfo.dwLength: 0x00000008
nandxipInfo.dwCodePages: 0
nandxipInfo.dwCopies: 0
nandxipInfo.dwBlockNo: 0x00000000
nandxipInfo.dwCodePages: 0
nandxipInfo.dwCopies: 0
}
Image block starts at physical block 51 virtual block 51
WARNING: OEMPlatformInit failed to initialize Ethernet controller.
g_iDevStatus = D!
SDMMC card is removed!
rSD_CUR_STATE = 0x880000
Press [ENTER] to download image now, or [SPACE] to enter boot monitor.

Initiating image download in 0 seconds.

Starting auto-download ...
Using device name: 'AT4X0HH_0'
InitDHCP():: Calling ProcessDHCP()
ProcessDHCP()::DHCP_INIT
NE2000SendFrame Timed out waiting for transmit buffers
NE2000SendFrame Timed out waiting for transmit buffers
NE2000SendFrame Timed out waiting for transmit buffers
NE2000SendFrame Timed out waiting for transmit buffers
Acum ce sa trebuie fac?

[chacka]

VanCroft esti de belea.Nu sti tu exact la ce e bun AtlasMgr dar i-mi place ca insisti.AtlasMgr il folosesti la rescrierea OS daca procedura de update de pe card nu merge.Apropo, ai incercat metoda cu cardul ?

[VanCroft]

Da . Am incercat prima data cu cardul dar nu a mers.Si insist din doua motive: una - ca imi place sa invat cate ceva si doi ca aparatul e al unui prieten si trebe sa il fac cat mai repede. M-as bucura daca mi-ai spune pe pasi ce trebuie mai exact sa fac. Iti multumesc tie si la ablbd ca ma bagati in seama si ma ajutati

[ablbd]

SDMMC card is detected!
Command or data time out!
SDMMC_Init successfully!

Am spus de nenumarate ori ca ca se lucreaza cu atlasmgr FARA CARD SD in aparat!!! Daca asa intelegi sa respecti indicatiile atunci mai bine renunta...

Apoi
Press [ENTER] to download image now, or [SPACE] to enter boot monitor.

Oare de ce nu ai apasat in acel moment [Space]??

[VanCroft]

Ok imi pare rau , nu am vrut sa intru cu cardul , l-am uitat in aparat; dar pot sa ma conectez iar la AtlasMgr si o sa apas pe space.Dupa aceea o sa-ti scriu ce imi arata , daca nu abuzez prea mult de voi.

[VanCroft]

M-am conectat si am apasat pe space cand mi-a cerut dar tot asa imi arata :
Starting auto-download ...
Using device name: 'AT4X0HH_0'
InitDHCP():: Calling ProcessDHCP()
ProcessDHCP()::DHCP_INIT
NE2000SendFrame Timed out waiting for transmit buffers
NE2000SendFrame Timed out waiting for transmit buffers
NE2000SendFrame Timed out waiting for transmit buffers
NE2000SendFrame Timed out waiting for transmit buffers

[chacka]

Cred ca ai uitat sa apesi Enter dupa Space.Urmatoarea comanda e ''F'' ,il lasi sa-si faca treaba apoi "U" , se activeaza butonul "Update NK Image apesi pe el , se deschide explorer , selectezi chain.lst din folderul cu firmware si cam atat

[VanCroft]

Am facut exact ce mi-ai spus si mi-a dat asta de mai jos care cred ca s-a realizat cu succes pentru ca mi-a pornit conectarea cu activesync si mi-a aparut pe ecranul aparatului navigatia , multimedia si setarile. Cred ca pot sa deconectez de la AtlasMgr nu ?
Va multumesc din tot sufletul ! Va doresc multa bafta si succes in continuare !!
Initiating image download in 13 seconds.
IsValidMBR: MBR sector = 0xCC0

OpenPartition: Partition Exists=0x0 for part 0x12.

GetReadOnlyPartInfo: READ-ONLY partition have not created.

BS-EBOOT:R3.0

Ethernet Boot Loader Configuration:
---------------------------------------
1) IP address: 0.0.0.0
Subnet mask: 0.0.0.0
2) Boot delay: 15 seconds
3) DHCP: ENABLED
4) Max Bad blocks reserved: 10
5) Startup image: DOWNLOAD NEW
6) Program RAM image into Boot Media: ENABLED
7) MAC address: 00:00:00:00:00:00
8) Bluetooth address: 00:00:00:00:00:00
9) Format Boot Media for BinFS
0) Format Boot Media for Monolithic NK Image

A) UPDATE image from SD/MMC card
B) UPDATE logo from SD/MMC card
D) DOWNLOAD image now
F) Low-level FORMAT Boot Media
N) New NANDFLASH Driver: DISABLED
L) LAUNCH existing Boot Media image
S) Save Configuration and Exit
U) Using AtlasMgr to download NK image
I) DOWNLOAD image via USB RNDIS Ethernet
R) LAUNCH existing Boot Media image via USB RNDIS KITL
C) Read-Only User FAT partition (type 0x12) block num: 3331
P) Read-Only User FAT partition (type 0x12): Writable
V) Image check sum
X) Clean Hive Partition
G) Dump Flash
T) Debug NandFlash
---------------------------------------

Enter your selection: f
Low-level format Blocks [0x33 - 0x7FF] ...
...format complete.
IsValidMBR: MBR sector = 0xFFFFFFFF

OpenPartition: Invalid MBR. Cannot open existing partition 0x12.

GetReadOnlyPartInfo: READ-ONLY partition have not created.

BS-EBOOT:R3.0

Ethernet Boot Loader Configuration:
---------------------------------------
1) IP address: 0.0.0.0
Subnet mask: 0.0.0.0
2) Boot delay: 15 seconds
3) DHCP: ENABLED
4) Max Bad blocks reserved: 10
5) Startup image: DOWNLOAD NEW
6) Program RAM image into Boot Media: ENABLED
7) MAC address: 00:00:00:00:00:00
8) Bluetooth address: 00:00:00:00:00:00
9) Format Boot Media for BinFS
0) Format Boot Media for Monolithic NK Image

A) UPDATE image from SD/MMC card
B) UPDATE logo from SD/MMC card
D) DOWNLOAD image now
F) Low-level FORMAT Boot Media
N) New NANDFLASH Driver: DISABLED
L) LAUNCH existing Boot Media image
S) Save Configuration and Exit
U) Using AtlasMgr to download NK image
I) DOWNLOAD image via USB RNDIS Ethernet
R) LAUNCH existing Boot Media image via USB RNDIS KITL
C) Read-Only User FAT partition (type 0x12) block num: 3331
P) Read-Only User FAT partition (type 0x12): Writable
V) Image check sum
X) Clean Hive Partition
G) Dump Flash
T) Debug NandFlash
---------------------------------------

Enter your selection: u
ROMHDR at Address 8C750044h
::OEMLaunch, ImageStart:0x8C750000, ImageLength:0x291560, LaunchAddr:0x8C751000
OEMLaunch: Write image to nandflash
OEMLaunch: (IMAGE_TYPE_MXIP|IMAGE_TYPE_BINFS)
+WriteRegionsToBootMedia: ImageStart: 0x8C750000, ImageLength: 0x291560, LaunchAddr:0x8C751000
INFO: OEMLaunch: Found chain extenstion: '' @ 0x8C750000
INFO: OEMLaunch: Found chain extenstion: 'chain information' @ 0x8C750000
INFO: OEMLaunch: Found 'chain information' (pChainInfo=0x8E17FE54 Extensions=0x4).
Found the Chain region: StartAddress: 0x8C44C000; Length: 0x000007B8
Writing multi-regions
BINFSPartMaxLength[0]: 0x4000, TtlBINFSPartLength: 0x4000
dwMaxRegionLength[3]: 0x4000
BINFSPartMaxLength[1]: 0x480000, TtlBINFSPartLength: 0x484000
dwMaxRegionLength[0]: 0x480000
BINFSPartMaxLength[2]: 0x250000, TtlBINFSPartLength: 0x6D4000
dwMaxRegionLength[1]: 0x250000
BINFSPartMaxLength[3]: 0x1D00000, TtlBINFSPartLength: 0x23D4000
dwMaxRegionLength[2]: 0x1D00000
Open/create BINFS partition 18368 sectors...
IsValidMBR: MBR sector = 0xFFFFFFFF

OpenPartition: Invalid MBR. Formatting flash.

Enter LowLevelFormat [0x0, 0x7FF].

Erasing flash block(s) [0x0, 0x7FF] (please wait):
######### dwBadBlocks=0 dwMaxBadBlocks=10.

Done.

WriteMBR: MBR block = 0x33.

Done.



OpenPartition: Partition Exists=0x0 for part 0x21.

CreatePartition: Enter CreatePartition for 0x21.

LastLogSector: Last log sector is: 0x1F03F.

CreatePartition: Start = 0x1, Num = 0x47BF.

Log2Phys: Logical 0x1 -> Physical 0xCC1

WriteMBR: MBR block = 0x33.

dwRegionStart: 0x8E000000, dwRegionLength: 0x291560, dwStoreOffset: 0x0
BP_SetDataPointer at 0x0

WriteData: Start = 0x0, Length = 0x291560.

Log2Phys: Logical 0x1 -> Physical 0xCC1

Updateded TOC!
dwRegionStart: 0x8E291560, dwRegionLength: 0x2073DC, dwStoreOffset: 0x480000
BP_SetDataPointer at 0x480000

WriteData: Start = 0x480000, Length = 0x2073DC.

Log2Phys: Logical 0x901 -> Physical 0x15C1

dwRegionStart: 0x8E49893C, dwRegionLength: 0xFE9D50, dwStoreOffset: 0x6D0000
BP_SetDataPointer at 0x6D0000

WriteData: Start = 0x6D0000, Length = 0xFE9D50.

Log2Phys: Logical 0xDA1 -> Physical 0x1A61

dwRegionStart: 0x8F48268C, dwRegionLength: 0x7B8, dwStoreOffset: 0x23D0000
BP_SetDataPointer at 0x23D0000

WriteData: Start = 0x23D0000, Length = 0x7B8.

Log2Phys: Logical 0x47A1 -> Physical 0x54A1

Written Chain Region to the Flash
LoadAddress = 0x8C44C000; FlashAddress = 0x000054A1; Length = 0X00000008


IsValidMBR: MBR sector = 0xCC0

OpenPartition: Partition Exists=0x1 for part 0x21.

Image start sector: 3265, total sectors: 18367

Please wait for calculating checksum...

CUR: ImageDataCheckSum: 0x7A16E18B, ImageInfoCheckSum: 0x149BCEA

TOC: ImageDataCheckSum: 0x7A16E18B, ImageInfoCheckSum: 0x149BCEA

*** colin edit: skip---->Create a Read-Only FATFS partition to store write-protected APP **
FindFreeSector: FreeSector is: 0x47C0 after processing part 0x21.

IsValidMBR: MBR sector = 0xCC0

OpenPartition: Partition Exists=0x0 for part 0x4.

CreatePartition: Enter CreatePartition for 0x4.

FindFreeSector: FreeSector is: 0x47C0 after processing part 0x21.

CreatePartition: Start = 0x47C0, Num = 0x1A100.

WriteMBR: MBR block = 0x33.

Creating a additional hide FAT partition to store hive-based registry
IsValidMBR: MBR sector = 0xCC0

OpenPartition: Partition Exists=0x0 for part 0x11.

CreatePartition: Enter CreatePartition for 0x11.

FindFreeSector: FreeSector is: 0x47C0 after processing part 0x21.

FindFreeSector: FreeSector is: 0x1E8C0 after processing part 0x4.

CreatePartition: Start = 0x1E8C0, Num = 0x640.

WriteMBR: MBR block = 0x33.

-WriteRegionsToBootMedia
FindFreeSector: FreeSector is: 0x47C0 after processing part 0x21.

FindFreeSector: FreeSector is: 0x1E8C0 after processing part 0x4.

FindFreeSector: FreeSector is: 0x1EF00 after processing part 0x11.

GetBaseFMDBlock: MBR block 51, Total Unusable Blk 53, start logic sector 0x1EF00
Start block NO. for new FMD driver should be 0x7F8
+TOC_Write
Erasing Block: 1

-TOC_Write
TOC {
dwSignature: 0x434F544E
BootCfg {
ConfigFlags: 0x3860
BootDelay: 0xF
ImageIndex: 1
IP: 0.0.0.0
MAC Address: 00:00:00:00:00:00
Port: 0.0.0.0
SubnetMask: 0.0.0.0
}
ID[0] {
dwVersion: 0x300B
dwSignature: 0x45424F54
String: 'eboot.nb0'
dwImageType: 0x2
dwTtlSectors: 0x280
dwLoadAddress: 0x8C04C000
dwJumpAddress: 0x8C04C000
dwStartBlock: 0x2
dwStoreOffset: 0x0
sgList[0].dwSector: 0x80
sgList[0].dwLength: 0x280
}
ID[1] {
dwVersion: 0x1
dwSignature: 0x43465348
String: 'PPC2K3.NB0'
dwImageType: 0xE
dwTtlSectors: 0x523
dwLoadAddress: 0x8C750000
dwJumpAddress: 0x8C751000
dwStartBlock: 0x33
dwStoreOffset: 0x0
sgList[0].dwSector: 0xCC1
sgList[0].dwLength: 0x523
}
chainInfo.dwLoadAddress: 0x8C44C000
chainInfo.dwFlashAddress: 0x000054A1
chainInfo.dwLength: 0x00000008
nandxipInfo.dwCodePages: 0
nandxipInfo.dwCopies: 0
nandxipInfo.dwBlockNo: 0x00000000
nandxipInfo.dwCodePages: 0
nandxipInfo.dwCopies: 0
}

Jumping to image at virtual address 0x8C751000h
+ToPhysicalAddr:0x8C751000
-ToPhysicalAddr:0xC0751000

::: Physical Launch Address: 0xC0751000h

[ablbd]

E OK, cu singura obiectiune ca ar fi fost mai bine ca in loc de "F" sa fi folosit "9"... Ideea este ca optiunea F formateaza doar o parte a nandului (cea cu bootloaderele, relativ periculos!!!) pe cind 9 nu se atinge de zona bootloaderelor ci formateaza apoi repartitioneaza restul nandului, stergind implicit si partitia ce contine registrii. Asta pentru viitor. Afara de asta, in scopul scurtarii timpului de bootare, de regula obisnuiesc sa modific "boot delay" de la 15s la 5s.

[VanCroft]

Iti multumesc. O intrebare as mai avea: aparatul a fost cumparat cu soft Mireo viaGPS 3.0 Black Edition (04.09.2009) si harti din 2009 care le-am pus la loc in aparat.Daca as vrea sa-i fac un update la harti trebe sa-i fac si la soft sau numai la harti? Si ce harti ii trebuie criptate sau decriptate ?

[ablbd]

Soft+harti, dar pentru lucrurile astea ar trebui sa vizitezi forumuri "specializate" pe asa ceva.